Koolance PC3-736SL Manual do Utilizador

Protected by U.S. Patents 6,664,627; 6,313,990; 6,234,240; 5,731,954Other Technology Pending U.S. & World-Wide PatentsSuperior Liquid Cooling Sys

5User ManualLED Display PanelTemperature SensorsPC3-700 systems can monitor up to 3 temperature sensors (included). The fi rst LED digit indicates whic

6Alarm SettingsBy default, the Koolance audio alarm will sound if any sensor reaches 55ºC (131ºF). When the system alarm sounds, the LED temperature w

7User ManualChapter2Connecting PC3-700 Systems

8Power ConnectionYou may begin the installation of your Koolance system by mounting a power supply in the chassis. The liquid cooling system requires

9User ManualATX Power SwitchThe ATX “pass through” lead is responsible for shutting off your computer if sensor channel #1 reaches 3ºC (5ºF) above th

10Depending on the cooling blocks (“coolers”) in your Koolance system and nozzle sizes (1/4”, 3/8”, etc.), they may be connected in series, parallel,

11User ManualThe maximum number of coolers allowed in a system will depend upon your specifi c thermal requirements and hose confi guration. It is not u

12Each tubing connection uses a threaded compression fi tting (“hose screw”) to keep it secure. To connect these components:Connecting HosesThread a ho

13User ManualDisconnecting HosesNozzles are designed to attach tightly. If you need to remove a hose for any reason, it may not pull off easily, even

14Hose LengthsRemove the threaded compression fi ttings from both radiator nozzles inside the case and attach the supplied 10mm (3/8”) tubing to each r

iUser ManualThis User Manual is updated regularly. Please be sure to check our support page for a newer version of this guide: www.koolance.com/suppor

15User ManualContinue connecting all of your coolers in the system until there are no longer any open tube ends.Liquid CoolersYou should now install t

16Chapter3Filling & MaintenanceFilling & Maintenance

17User ManualTesting & FillingOnce all of the coolers have been connected, the system can be fi lled with coolant. The refi ll tap is located on top

18The liquid coolant should be fi lled up to about 1.5 cm (1/2”) from the reservoir’s top. This small gap will catch air as it circulates through the s

19User ManualThe coolant in your system should be emptied for any of the below reasons. Unless replacing the liquid coolant, it can also be reused.1.

20We hope your Koolance system will provide you with years of reliable cooling performance. To help avoid unnecessary RMA issues, we have prepared thi

21User Manual4. After the system has been on for awhile, the temperature alarm sounds...Make sure the LED temperature is at or above your preset alarm

226. My system appears to be leaking fl uid...Since users are allowed to confi gure their own coolers and clamps, it is possible a connection was not pr

23User ManualLimited WarrantyDisclaimerKoolance Incorporated (“Koolance”) warrants each new Koolance liquid-cooled system (“the system”), against defe

Protected by U.S. Patents 6,664,627; 6,313,990; 6,234,240; 5,731,954Other Technology Pending U.S. & World-Wide PatentsSuperior Liquid Cooling Sys

iiWARNING: The Koolance liquid & coolant pack contain chemicals which may be harmful or fatal if swallowed. KEEP THIS AND ALL DANGEROUS CHEMICAL

iiiUser ManualTable of ContentsIntroduction 1PC3-700 System Diagram ... 4LE

iv PC3 Series Systems: - motherboard standoffs & insulating washers - motherboard, slot card, 5.25” drive, and fl oppy screws - hard drive moun

1User ManualChapter1Introduction

2 Congratulations on your purchase of a Koolance system!As the most sophisticated product of its kind, Koolance offers many unique features found now

3User ManualThe heart of a liquid cooling system is the pump. This device pushes liquid through each cooler and into the heat exchanger. Koolance syst

4 IntroductionPC3-700 System DiagramReservoir & Pumps Radiator Cooling FansReservoir Refi ll TapRadiator (Primary Heat Exchanger)Power Circuit B